4 Knowledge Base

 

 TelecomTrainning.net > Knowledge Base
 Viewing KB Article
Good Evening, - Please register or - log-in to your account.
Search
Search   Saved Questions   Ask a question
Keywords 
 
Available categories
LTE
100 of Questions in LTE
CCNA Certification
CCNA Sample Q & A (1000 + Q &A)
(Network +) Certification
(Network +) Sample Q & A (1000 + Q &A)
Networking
General/Interview Q& A on Networking
Home Networking
General/Interview Q& A on Networking
VOIP, SIP & Asterisk
Q & A on VOIP,Ethereal, SIP & Asterisk
Telecom Test Equipments
Q & A on Telecom Test Equipment
PSTN / Wireline
General / Interview Q & A on PSTN / Wireline
LTE, Wireless, 3G ,Diameter and HSS
General/Interview Q & A on LTE, Wireless, 3G ,Diameter and HSS
Telecom General
Any Q & A in Telecom in General

Top Questions
Friends, Describe Secure storage and distribution of A-Keys?
How do I monitor SS7 Traffic in spectra2?
what is the difference between E1 signal & Ethernet signal ?
Explain me the difference between a repeater, bridge and router? Relate this to the OSI model.
What is the difference between BRI & PRI ?
Can you tell me about PBGT?
Guys what is the purpose of Umbrella Cell Approach in GSM ?
how can we explain media gateway in MSc?
What is GGSN?
What is the difference between Electrical-tilt and Mechanical-tilt of an antenna?
What is BSC?
Can any one explain me how sms flow will work using ss7 network ?( from physical layer to application layer)
What is demarc point?
Explain SLTA and SLTM messages in MTP3?
why cellphone towers are painted in red and white?
Hi guys what is WAP?
what is EDAp? what is the functions of EDAP?
wat is the difference betweem MSC & GMSC, & MSS & GCS?
what is sdh?
What is a circuit id?

If synchronisation between BSC to BTS fail,what will happen?
sarathy_26 20-August-2008 03:34:24 PM

Comments


If Synchronization fails between BSC and BTS, the clock signal from BSC will not reaches to BTS and Abis link goes down and supervision not possible and we cant perform any operations at that site.
Posted by sagitraz


If yhe link is down ,then we use 2nd link ..means we use other bsc.we conect our bts with other bsc also.simply is that
Posted by saqlain231


The whole communication could create a mess.And blocks whole communication.
Posted by sagitraz


The whole communication could create a mess.And blocks whole communication.
Posted by sagitraz


Basically a fluctuation in Abis link and you can check it through a simple LED or with a BERT meter & you can also called it that LAPD is in break.
Posted by jahangir1983


Basically a fluctuation in Abis link and you can check it through a simple LED or with a BERT meter & you can also called it that LAPD is in break.
Posted by jahangir1983


If BTS-B fails to allocate resources to the MS, resources at BTS-A will not be .... to the MS after synchronization between the MS and BTS-B is achieved,A BTS will cover a specific geographical area depending on the location and ... If an MSC also acts as a switching centre between the PLMN
Posted by waqasahmad


If Synchronization fails between BSC and BTS, the clock signal from BSC will not reaches to BTS and Abis link goes down and supervision not possible and we cant perform any operations at that site.
Posted by yellaiah


In short when BTS link fail with BSC then an critical alarm is generated at the MSC end which is basically RED alert that communication is break and the channels are not available through that BTS
Posted by HamidAliKhan


Simply your whole communication is disturb.
Posted by waqqas1

Q&A Rating

Q&A Rating
Rate This Question and Answer

Related Questions
Hello,Plz Tell me about and 3G interoperability.
 
I can access Intenet from IBM labtop but I do not see the wireless icon in windows?
 
Explain the SIP “Service” address format?


Search questions via popularity
Top viewed questions  Top emailed questions  Most printed questions  Most saved questions
 
Copyright © Telecom Training, All Rights Reserved