|
I need help; what is IEEE 802.3? Gustavo 03-October-2007 06:18:58 PMComments en.wikipedia.org/wiki/IEEE_802.3 Posted by crouse www.webopedia.com/TERM/I/IEEE_802_standards.html Posted by saqlain231 IEEE 802.3 is a collection of IEEE standards defining the physical layer, and the media access control (MAC) sublayer of the data link layer, of wired Ethernet. This is generally a LAN technology with some WAN applications. Physical connections are made between nodes and/or infrastructure devices (hubs, switches, routers) by various types of copper or fiber cable. 802.3 is a technology that can support the IEEE 802.1 network architecture. The maximum packet size is 1518 bytes, although to allow the Q-tag for Virtual LAN and priority data in 802.3ac it is extended to 1522 bytes. If the upper layer protocol submits a protocol data unit (PDU) less than 64 bytes, 802.3 will pad the data field to achieve the minimum 64 bytes. The minimum Frame size will then always be of 64 bytes. Although it is not technically correct, the terms packet and frame are often used interchangeably. The ISO/IEC 8802-3 and ANSI/IEEE 802.3 standards refer to MAC sub-layer frames consisting of the destination address, the source address, length/type, data payload, and frame check sequence (FCS) fields. The preamble and Start Frame Delimiter (SFD) are (usually) together considered a header to the MAC frame. This header and the MAC frame constitute a packet. The original Ethernet is called Experimental Ethernet today. It was developed by Robert Metcalfe in 1972 (patented in 1978) and was based in part on the wireless ALOHAnet protocol. The first Ethernet that was generally used outside Xerox was DIX Ethernet, followed by Ethernet II. IEEE defines a 802.3 standard where the Type field is replaced by Length, and an 802.2 LLC header follows with the Type field. However, as DIX Ethernet was derived from Experimental Ethernet, and as many standards have been developed that are based on DIX Ethernet, the technical community has accepted the term Ethernet for all of them. Therefore, the term Ethernet can be used to name networks using any of the following standardized media and functions: Posted by waqasahmad standard for Ethernet networking protocol. Posted by HamidAliKhan The standard defining early forms of the Ethernet networking protocol. Posted by Christ |
Posted: 03-October-2007 06:38:56 PM By: Christ The standard defining early forms of the Ethernet networking protocol. | |
Posted: 29-November-2008 01:52:43 PM By: HamidAliKhan standard for Ethernet networking protocol. | |
Posted: 02-March-2009 02:51:46 AM By: waqasahmad IEEE 802.3 is a collection of IEEE standards defining the physical layer, and the media access control (MAC) sublayer of the data link layer, of wired Ethernet. This is generally a LAN technology with some WAN applications. Physical connections are made between nodes and/or infrastructure devices (hubs, switches, routers) by various types of copper or fiber cable. 802.3 is a technology that can support the IEEE 802.1 network architecture. The maximum packet size is 1518 bytes, although to allow the Q-tag for Virtual LAN and priority data in 802.3ac it is extended to 1522 bytes. If the upper layer protocol submits a protocol data unit (PDU) less than 64 bytes, 802.3 will pad the data field to achieve the minimum 64 bytes. The minimum Frame size will then always be of 64 bytes. Although it is not technically correct, the terms packet and frame are often used interchangeably. The ISO/IEC 8802-3 and ANSI/IEEE 802.3 standards refer to MAC sub-layer frames consisting of the destination address, the source address, length/type, data payload, and frame check sequence (FCS) fields. The preamble and Start Frame Delimiter (SFD) are (usually) together considered a header to the MAC frame. This header and the MAC frame constitute a packet. The original Ethernet is called Experimental Ethernet today. It was developed by Robert Metcalfe in 1972 (patented in 1978) and was based in part on the wireless ALOHAnet protocol. The first Ethernet that was generally used outside Xerox was DIX Ethernet, followed by Ethernet II. IEEE defines a 802.3 standard where the Type field is replaced by Length, and an 802.2 LLC header follows with the Type field. However, as DIX Ethernet was derived from Experimental Ethernet, and as many standards have been developed that are based on DIX Ethernet, the technical community has accepted the term Ethernet for all of them. Therefore, the term Ethernet can be used to name networks using any of the following standardized media and functions: | |
Posted: 07-June-2009 11:09:08 AM By: saqlain231 www.webopedia.com/TERM/I/IEEE_802_standards.html | |
Posted: 18-September-2009 04:34:42 AM By: crouse en.wikipedia.org/wiki/IEEE_802.3 |