2 Knowledge Base

 

 TelecomTrainning.net > Knowledge Base > CCNA Certification
 Article Listings
Good Morning, - Please register or - log-in to your account.
Search
Search   Saved Questions   Ask a question
Keywords 
 
Available categories
LTE
100 of Questions in LTE
CCNA Certification
CCNA Sample Q & A (1000 + Q &A)
(Network +) Certification
(Network +) Sample Q & A (1000 + Q &A)
Networking
General/Interview Q& A on Networking
Home Networking
General/Interview Q& A on Networking
VOIP, SIP & Asterisk
Q & A on VOIP,Ethereal, SIP & Asterisk
Telecom Test Equipments
Q & A on Telecom Test Equipment
PSTN / Wireline
General / Interview Q & A on PSTN / Wireline
LTE, Wireless, 3G ,Diameter and HSS
General/Interview Q & A on LTE, Wireless, 3G ,Diameter and HSS
Telecom General
Any Q & A in Telecom in General

Top Questions
Friends, Describe Secure storage and distribution of A-Keys?
How do I monitor SS7 Traffic in spectra2?
what is the difference between E1 signal & Ethernet signal ?
Explain me the difference between a repeater, bridge and router? Relate this to the OSI model.
What is the difference between BRI & PRI ?
Can you tell me about PBGT?
Guys what is the purpose of Umbrella Cell Approach in GSM ?
how can we explain media gateway in MSc?
What is GGSN?
What is the difference between Electrical-tilt and Mechanical-tilt of an antenna?
What is demarc point?
What is BSC?
Can any one explain me how sms flow will work using ss7 network ?( from physical layer to application layer)
Explain SLTA and SLTM messages in MTP3?
why cellphone towers are painted in red and white?
Hi guys what is WAP?
what is EDAp? what is the functions of EDAP?
wat is the difference betweem MSC & GMSC, & MSS & GCS?
what is sdh?
What is a circuit id?

CCNA Certification
I need help; how would you configure it so you could type in the hostname "Randy" instead of the IP address to access the remote router named Randy?
Cornelius - 02-September-2007 06:05:00 PM
 Hi which command can you type to view the hostnames configured in your router ?
Brenton - 02-September-2007 06:04:49 PM
 Anyone tell me, what frame type does CDP use to gather information about its directly connected neighbors?
Triston - 01-September-2007 06:04:17 PM
 Friends I have a doubt that, what’s the default CDP update broadcast rate?
Colton - 01-September-2007 06:04:03 PM
 Hi guys what’s the default CDP hold time?
Ismael - 01-September-2007 06:03:50 PM
 Friends you just received an output that states the CDP hold time, hardware, port ID, and local interface of a remote router. What was the command did you enter?
Shreyas - 01-September-2007 06:03:31 PM
 Friends I have a doubt that ,What is the default administrative distance for IGRP?
Chris - 01-September-2007 06:03:17 PM
 Hello friends, what is the default administrative distance of RIP?
David - 01-September-2007 06:01:16 PM
 What type of routing protocols send their entire routing table every 30 seconds?
Issac - 01-September-2007 06:00:21 PM
 Help me what is convergence?
Coleman - 01-September-2007 06:00:00 PM
 
Page:  1  2  3  4  5  6  7  8  9  10  11  12  13  14  15  16  17  18  19  20  21  22  23  24  25  26  27  28  29  30  31  32  33  34  35  36  37  38  39 40  41  42  43  44  45  46  47  48  49  50  51  52  53  54  55  56  57  58  59  60  61  62  63  

Search questions via popularity
Top viewed questions  Top emailed questions  Most printed questions  Most saved questions
 
Copyright © Telecom Training, All Rights Reserved