2 Knowledge Base

 

 TelecomTrainning.net > Knowledge Base > CCNA Certification
 Article Listings
Good Morning, - Please register or - log-in to your account.
Search
Search   Saved Questions   Ask a question
Keywords 
 
Available categories
LTE
100 of Questions in LTE
CCNA Certification
CCNA Sample Q & A (1000 + Q &A)
(Network +) Certification
(Network +) Sample Q & A (1000 + Q &A)
Networking
General/Interview Q& A on Networking
Home Networking
General/Interview Q& A on Networking
VOIP, SIP & Asterisk
Q & A on VOIP,Ethereal, SIP & Asterisk
Telecom Test Equipments
Q & A on Telecom Test Equipment
PSTN / Wireline
General / Interview Q & A on PSTN / Wireline
LTE, Wireless, 3G ,Diameter and HSS
General/Interview Q & A on LTE, Wireless, 3G ,Diameter and HSS
Telecom General
Any Q & A in Telecom in General

Top Questions
Friends, Describe Secure storage and distribution of A-Keys?
How do I monitor SS7 Traffic in spectra2?
what is the difference between E1 signal & Ethernet signal ?
Explain me the difference between a repeater, bridge and router? Relate this to the OSI model.
What is the difference between BRI & PRI ?
Can you tell me about PBGT?
Guys what is the purpose of Umbrella Cell Approach in GSM ?
how can we explain media gateway in MSc?
What is GGSN?
What is the difference between Electrical-tilt and Mechanical-tilt of an antenna?
What is demarc point?
What is BSC?
Can any one explain me how sms flow will work using ss7 network ?( from physical layer to application layer)
Explain SLTA and SLTM messages in MTP3?
why cellphone towers are painted in red and white?
Hi guys what is WAP?
what is EDAp? what is the functions of EDAP?
wat is the difference betweem MSC & GMSC, & MSS & GCS?
what is sdh?
What is a circuit id?

CCNA Certification
Hi which OSI layer is responsible for addressing devices and routing through an internet work?
Henry - 16-August-2007 03:05:24 PM
 Hello friends, Which OSI layer is responsible for putting Is and 0s into a logical group?
Cornelius - 16-August-2007 03:05:06 PM
 Hi a Unique ID placed in the header of each frame as it travels the switch fabric with a user-assigned ID defined in each frame is known as?
Issac - 16-August-2007 03:04:48 PM
 Friends I have a doubt that how do you display your configured DLCI's on a frame-relay router?
Jagger - 16-August-2007 03:04:32 PM
 Friends I have a doubt how do I enable IPX on a router?
Milton - 16-August-2007 03:04:10 PM
 Tell me How do you display the ipx routing updates in or out between routers?
Connor - 16-August-2007 03:03:53 PM
 Friends I have a doubt you have an IP address of 153.50.6.27 and a subnet mask of 255.255.255.128. What is the class,how many bits are being subnetted, and what is the broadcast address?
Eshwardutt - 16-August-2007 03:03:34 PM
 Friends I have a doubt what does the ipx maximum paths command do?
Tyson - 16-August-2007 03:02:28 PM
 Hello friends, what are the 2 steps used to configure and access list?
Cornelius - 15-August-2007 03:02:09 PM
 Friends I have a doubt that i have network 145.100.0.0 with a subnet mask of 255.255.248.0. If an access list is applied to address 145.100.8.0 with a wildcard mask of 0.0.7.255, what address range will it filter?Be the First one to answer this Question
Colt - 15-August-2007 03:01:55 PM
 
Page:  1  2  3  4  5  6  7  8  9  10  11  12  13  14  15  16  17  18  19  20  21  22  23  24  25  26  27  28  29  30  31  32  33  34  35  36  37  38  39  40  41  42  43  44  45  46  47  48  49  50  51 52  53  54  55  56  57  58  59  60  61  62  63  

Search questions via popularity
Top viewed questions  Top emailed questions  Most printed questions  Most saved questions
 
Copyright © Telecom Training, All Rights Reserved