4 Knowledge Base

 

 TelecomTrainning.net > Knowledge Base
 Viewing KB Article
Good Morning, - Please register or - log-in to your account.
Search
Search   Saved Questions   Ask a question
Keywords 
 
Available categories
LTE
100 of Questions in LTE
CCNA Certification
CCNA Sample Q & A (1000 + Q &A)
(Network +) Certification
(Network +) Sample Q & A (1000 + Q &A)
Networking
General/Interview Q& A on Networking
Home Networking
General/Interview Q& A on Networking
VOIP, SIP & Asterisk
Q & A on VOIP,Ethereal, SIP & Asterisk
Telecom Test Equipments
Q & A on Telecom Test Equipment
PSTN / Wireline
General / Interview Q & A on PSTN / Wireline
LTE, Wireless, 3G ,Diameter and HSS
General/Interview Q & A on LTE, Wireless, 3G ,Diameter and HSS
Telecom General
Any Q & A in Telecom in General

Top Questions
Friends, Describe Secure storage and distribution of A-Keys?
How do I monitor SS7 Traffic in spectra2?
what is the difference between E1 signal & Ethernet signal ?
Explain me the difference between a repeater, bridge and router? Relate this to the OSI model.
What is the difference between BRI & PRI ?
Can you tell me about PBGT?
Guys what is the purpose of Umbrella Cell Approach in GSM ?
how can we explain media gateway in MSc?
What is GGSN?
What is the difference between Electrical-tilt and Mechanical-tilt of an antenna?
What is BSC?
Can any one explain me how sms flow will work using ss7 network ?( from physical layer to application layer)
What is demarc point?
Explain SLTA and SLTM messages in MTP3?
why cellphone towers are painted in red and white?
Hi guys what is WAP?
what is EDAp? what is the functions of EDAP?
wat is the difference betweem MSC & GMSC, & MSS & GCS?
what is sdh?
What is a circuit id?

How do I monitor VOIP Traffic in spectra2?
parveesh 31-August-2007 01:17:48 PM

Comments


You may monitor VOIP Traffic in spectra2 by following 1.)First Create Sys Conf
2.)Conf Board Properties
3.)Conf Ethernet Port
4.)Enter Ip address range
5.)Select Port definition
6.)Select N/w Conf
7.)Click voip tool and place monitor voip
8.)Enter name of voip network for monitoring
9.)Assign ports
10)And finally click ok,run,capture and save
captured files.
Posted by HamidAliKhan


1.)First Create Sys Conf
2.)Conf Board Properties
3.)Conf Ethernet Port
4.)Enter Ip address range
5.)Select Port definition
6.)Select N/w Conf
7.)Click voip tool and place monitor voip
8.)Enter name of voip network for monitoring
9.)Assign ports
10)And finally click ok,run,capture and save
captured files.
Posted by waqqas1


Just follow the below procedure:

1.)First Create Sys Conf
2.)Conf Board Properties
3.)Conf Ethernet Port
4.)Enter Ip address range
5.)Select Port definition
6.)Select N/w Conf
7.)Click voip tool and place monitor voip
8.)Enter name of voip network for monitoring
9.)Assign ports
10)And finally click ok,run,capture and save
captured files.
Posted by sagitraz


Open workspace -> click configuration ->configure board properties ->configure ethernet port with correct version -> click monitor option-> enter ip address range ->select port definition from configurtion tab, select correct port and transpor type -> save -> select network configuration-> click voip tool -> clikc network diagram area and place monitor voip ->enter the name of voip network to monitor ->assign the appropriate ports ->click ok to return to network configuration window -> click OK, RUN, Capture and also save the capture file to view the stats
Posted by viswanathan

Q&A Rating

Q&A Rating
Rate This Question and Answer

Related Questions
Explain glare?
 
Tell me that which disk is not needed with windows 2000 as Disk Management prepares hard disks
 
How to calculate subnet address, Can someone give example?


Search questions via popularity
Top viewed questions  Top emailed questions  Most printed questions  Most saved questions
 
Copyright © Telecom Training, All Rights Reserved