2 Knowledge Base


 TelecomTrainning.net > Knowledge Base > Networking
 Article Listings
Good Evening, - Please register or - log-in to your account.
Search   Saved Questions   Ask a question
Available categories
100 of Questions in LTE
CCNA Certification
CCNA Sample Q & A (1000 + Q &A)
(Network +) Certification
(Network +) Sample Q & A (1000 + Q &A)
General/Interview Q& A on Networking
Home Networking
General/Interview Q& A on Networking
VOIP, SIP & Asterisk
Q & A on VOIP,Ethereal, SIP & Asterisk
Telecom Test Equipments
Q & A on Telecom Test Equipment
PSTN / Wireline
General / Interview Q & A on PSTN / Wireline
LTE, Wireless, 3G ,Diameter and HSS
General/Interview Q & A on LTE, Wireless, 3G ,Diameter and HSS
Telecom General
Any Q & A in Telecom in General

Top Questions
Friends, Describe Secure storage and distribution of A-Keys?
How do I monitor SS7 Traffic in spectra2?
Explain me the difference between a repeater, bridge and router? Relate this to the OSI model.
what is the difference between E1 signal & Ethernet signal ?
What is the difference between BRI & PRI ?
Can you tell me about PBGT?
What is GGSN?
What is the difference between Electrical-tilt and Mechanical-tilt of an antenna?
What is BSC?
Guys what is the purpose of Umbrella Cell Approach in GSM ?
how can we explain media gateway in MSc?
Can any one explain me how sms flow will work using ss7 network ?( from physical layer to application layer)
Explain SLTA and SLTM messages in MTP3?
why cellphone towers are painted in red and white?
what is EDAp? what is the functions of EDAP?
wat is the difference betweem MSC & GMSC, & MSS & GCS?
what is sdh?
Hi guys what is WAP?
What is difference in between soft handover and hard handover in UMTS network ?
Friends, What is the purpose of Packet Control Unit in BSC?

In a network with dozens of switches, how many root bridges would you have?
hameznick - 02-June-2009 08:55:53 AM
 Which of the following would be good reasons to run NAT?
hameznick - 01-June-2009 02:37:47 AM
 Which of the following is considered to be the address after translation?
anders - 01-June-2009 02:37:41 AM
 You have 10 users plugged into a hub running 10Mbps half-duplex. There is a server connected to the switch running 10Mbps half-duplex as well. How much bandwidth does each host have to the server?
anders - 28-May-2009 03:08:26 AM
 What protocol does PPP use to identify the Network layer protocol?
hameznick - 28-May-2009 03:08:16 AM
 Which of the following commands connect access list 110 inbound to interface ethernet0?
anders - 27-May-2009 03:50:49 AM
 What command will permit SMTP mail to only host
michaelchristopher - 27-May-2009 03:50:08 AM
 Pat Address Translation is also termed what?
michaelchristopher - 26-May-2009 06:23:15 AM
 Which command would you place on interface connected to the Internet?
hameznick - 26-May-2009 06:23:09 AM
 Which of the following would be a good starting point for troubleshooting if your router is not translating?
michaelchristopher - 25-May-2009 07:24:58 AM
Page:  1  2  3  4 5  6  7  8  9  10  11  12  13  14  15  16  17  18  19  20  21  22  23  24  25  26  27  28  29  30  31  32  33  34  35  36  37  38  39  40  41  42  43  44  45  46  47  48  49  50  51  52  53  54  55  56  

Search questions via popularity
Top viewed questions  Top emailed questions  Most printed questions  Most saved questions
Copyright © Telecom Training, All Rights Reserved