4 Knowledge Base

 

 TelecomTrainning.net > Knowledge Base
 Viewing KB Article
Good Morning, - Please register or - log-in to your account.
Search
Search   Saved Questions   Ask a question
Keywords 
 
Available categories
LTE
100 of Questions in LTE
CCNA Certification
CCNA Sample Q & A (1000 + Q &A)
(Network +) Certification
(Network +) Sample Q & A (1000 + Q &A)
Networking
General/Interview Q& A on Networking
Home Networking
General/Interview Q& A on Networking
VOIP, SIP & Asterisk
Q & A on VOIP,Ethereal, SIP & Asterisk
Telecom Test Equipments
Q & A on Telecom Test Equipment
PSTN / Wireline
General / Interview Q & A on PSTN / Wireline
LTE, Wireless, 3G ,Diameter and HSS
General/Interview Q & A on LTE, Wireless, 3G ,Diameter and HSS
Telecom General
Any Q & A in Telecom in General

Top Questions
Friends, Describe Secure storage and distribution of A-Keys?
How do I monitor SS7 Traffic in spectra2?
Explain me the difference between a repeater, bridge and router? Relate this to the OSI model.
What is the difference between BRI & PRI ?
what is the difference between E1 signal & Ethernet signal ?
Can you tell me about PBGT?
What is GGSN?
What is BSC?
What is the difference between Electrical-tilt and Mechanical-tilt of an antenna?
Guys what is the purpose of Umbrella Cell Approach in GSM ?
how can we explain media gateway in MSc?
Can any one explain me how sms flow will work using ss7 network ?( from physical layer to application layer)
Explain SLTA and SLTM messages in MTP3?
why cellphone towers are painted in red and white?
what is EDAp? what is the functions of EDAP?
wat is the difference betweem MSC & GMSC, & MSS & GCS?
what is sdh?
What is difference in between soft handover and hard handover in UMTS network ?
Friends, What is the purpose of Packet Control Unit in BSC?
Explain how to configure a host network interface bge0 or bge1 or bge2 or bge3 with IP address?

Explain how to configure a host network interface bge0 or bge1 or bge2 or bge3 with IP address?
James 23-December-2007 01:49:46 PM

Comments


www.opensolaris.com/use/network_administration.pdf
Posted by crouse


www.opensolaris.org/os/.../networking/readme.hxbt
Posted by crouse


9. Also you need to add the IP or hostname exactly how it appear in /etc/host file and add that hostname or IP in /etc/ hostname.bge3
10. Either reboot or do Ifconfig bge3 down/up to bring the interface with new IP

Posted by Sandeepen


1. Document the current and new IP addresses, netmasks and static routes
2. Do a ifconfig a
3. Document cat /etc/hosts, cat /etc/netmask, netstat rn
4. Login as root
5. ifconfig bge# plumb example ifconfig bge3 plumb
6. ifconfig bge3 192.10.235.100 255.255.255.248 arp
Ignore an error message if it is displayed:
ifconfig: setifdstaddr: SIOCSLIFDSTADDR:bge3:Cannot assign requested address
7. check with ifconfig -a
8. Same applies for any other interface
Posted by Sandeepen

Q&A Rating

Q&A Rating
Rate This Question and Answer

Related Questions
Friends, Do you know how much voltage is required for Cisco FP phone?
What is the most common Layer 2 device?
 
Difference between synchronous & asynchronous communication.
 


Search questions via popularity
Top viewed questions  Top emailed questions  Most printed questions  Most saved questions
 
Copyright © Telecom Training, All Rights Reserved